DIY Speaker Cables are a great way to boost your home theater or audiophile setup without blowing wads of money. The big brands would like you to think their cables are made with some secret ingredient, guess what, there not. With some simple tools, some affordable parts, and a little know ways to create Cayin 300B that not only rival the sound quality of the big brands, however the appearance also. Simply follow the steps below.

Step 1: Gather the various tools and Parts – You will have to collect these tools: a measuring tape, a spool of yarn or string, a ruler, scissors, a tiny screwdriver or screwdriver set, an exacto knife or box cutter. After you have gathered your tools you need to buy the parts required to build the speaker cable. The parts include: your desired period of speaker wire 10-20% extra, the desired period of sleeving 10-20% extra, your selected end connectors, cable pants that are the proper size for your cable. Additionally you will need two sizes of heat shrink, and a roll of scotch tape.

Step Two: Measure and Cut – Should you be not sure what length cable you will require, run a bit of strong out of your stereo to your speaker pursuing the route you plan to run the speaker cable. Put in a foot or two depending on the overall length, and after that measure the size of the string.

Once you measure the length cut your speaker cable for the length you have calculated. Now measure the duration of one cable pant, and inside length of the connector (for instance in a banana plug the duration of the cable that will be inside the banana plug).

Go ahead and take number and double it. Now reduce your sleeving at a entire speaker cable minus the calculation from your pants and banana plug. Add an inch to get safe.

Step 3: Slide on the Sleeving – Now that you have the majority of your components measured out, it is actually time for you to slide on the sleeving. Should you used the chart from step two you ought to have no issue getting it within the cable. Utilize a slinky like motion to push the sleeving on the cable.

Slide about 4 to 5 inches at the same time, give it time to bunch up and then push the bunch further on the cable. For CopperColour Cable this may take a moment, show patience and simply keep repeating the slinky motion. If you wish to you can apply some scotch tape for the ends from the speaker cable in a cone like shape, this helps the cable slide from the sleeving without getting snagged.

Step 4: Apply the temperature Shrink – Now that you possess the sleeving on you may have noticed the ends are starting to fray, no reason to worry. Take your heat shrink (At the end of this article there are size recommendations) and cut off two half inch long pieces. You won’t be seeing this heat shrink in the long run, so don’t fret if its not really 50 % of an inch long, or if its not cut perfectly straight.

Take the heat shrink and slide it on the end in the sleeving, if the sleeving is just too frayed use a piece of scotch tape to temporarily hold on the fray, simply wrap the tape round the end from the sleeving, slide the temperature shrink on the tape and remove the scotch tape.

Don’t leave the tape as the next step might cause it to burn.

Once the heats hrink is positioned to pay for the fraying ends of the sleeving, make use of a lighter, heat gun or hairdryer to shrink the warmth shrink. Take care not to burn the heat shrink or perhaps the sleeving around it.

Step 5: Slide on the Cable Pants – The temperature shrink you applied in step 5 should alllow for a smooth installation of the speaker pants. Measure the size of the speaker cable through the end in the heat shrink for the end of the cable. It should be the size of the cable pants the useable length of your connector some extra. Take scissors or perhaps an Exacto knife and make a circular cut round the speaker cable sheath. Eliminate the sheath and shut down any cotton fiber that could have been utilized in the cable construction. You will now slide on the cable pants. In the event the individual legs in the pants have a hard time sliding on the speaker cable conductors, apply a small amount of dish soap for the speaker cable to aid in this process.

Once the cable pants are on you will want to slide them as far down as they possibly can go, and then backup about 1/4″. This will give you some room for error over the following step.

Step 6: Install the Connector – Using the sleeving, heat shrink and cable pants already on your cable you are almost done. The very last step is to use your choice of connector. You are able to choose between banana plugs, spades or pins. Whichever connector you decide on, the steps are the same. Depending on your connector you might need to slide the decorative cover within the cable pants prior to the following steps.

Unscrew the set screws. Slide the speaker cable with all the covering still on to the connector. Mark the cable as near to the connector as possible. Making use of the mark produced in step 3 strip the sheath off of the individual conductor. Slide off of the protective sheath, and after that slide the bare wire into the connector. (Try not to touch the bare wire together with your bare fingers as the qzuqtl is not going to assist the copper).

Tighten the set screws completely making certain they line up on the bare wire. Based on your connector setup, screw on the decorative cover. For the correct size components please reference the subsequent chart: DIY Speaker Cable Component Size There is not any limit towards the creativity you can use when creating you cables. You could add a piece of heat shrink over the top of joint involving the Line Magnetic 518ia, or use colored heat shrink to mark each conductor.

For additional color you can use multiple layers of sleeving, like metallic or glow-in-the-dark-clear over surface of a color of your choice. Finally ViaBlue makes great cable splitters that can be used rather than cable pants for more style.

Hifi RCA Cable – Learn More..

We are using cookies on our website

Please confirm, if you accept our tracking cookies. You can also decline the tracking, so you can continue to visit our website without any data sent to third party services.