This automatic optical Fiber tensile screening system is made for operator ability independent use within production and lab settings. Two fundamental design configurations enable the user to select from a set up for standard linear proof testing with extra mandrels for rotary high power testing.

The linear edition is made for creation evidence testing with causes up to 22 N. Motorized clamps with carefully designed rubberized inserts ensure that the Fiber coating is not damaged within the screening procedure whilst at the same time eliminating the requirement for an outside air supply. Degrees of pulling force, pulling speed and hold time are automated and easily offered to the FTTH Cable Production Line with the built in Liquid crystal display touch screen manage. Information from tests can be saved and reached using the USB port or Ethernet interface.

Mandrels of the same design as with NYFORS’ visual Fiber recoaters can be attached to the evidence tester inside the rotary higher power configuration. The Fiber is wrapped around the two mandrels which assistance it using a unique clamping system. By doing this higher loads can be used to the Fiber, allowing breaking strength tests below controlled circumstances.

Changeable clamp positioning facilitates testing with all the greatest force amounts as well as screening of brief Fiber measures. The lightweight and light bodyweight style definitely makes the tool simple to move around in Secondary Coating Line and also to incorporate in a production work bench where space are at reduced. The machine is actually a lightweight and lightweight tool suitable for testing the effectiveness of visual fibers up to 30 N. The device is developed to fulfill all types of applications in which a power check needs to be carried out.

The device is made with the user in mind. The Fiber is readily put into the guided linear clamps, and the testing starts automatically with a “One Touch” go switch. The built-in microprocessor regulates each of the essential parameters like tugging force, tugging speed and hold time. This allows for any completely controlled check each and every time.

The equipment can be connected to an external PC, which enables use of all automated parameters and configurations. The machine is adapted to face-alone use or even to the integration into different subsystems. The equipment posseses an substantial capacity for logging and conserving information including tugging force, tugging speed and Fiber size and other parameters.

Two recoat injector designs are available. The PTR307 uses a computerized pump to inject the recoat materials. The quantity of material dispensed through the automatic injector is controlled by hand using the top-mounted “Inject” switch or programmed in to the machine using the tablet controller. The PTR307B features a handbook recoat injection program that requires the consumer to manually distribute the recoat material into the mold cavity; another one injector for the PTR307B recoater is available listed below. Make sure you note that the automatic injector is just suitable for higher-index recoat materials, while the manual injector works with each reduced- and- directory recoat materials; they are both marketed individually below. Make sure you get in touch with Tech Assistance for additional information.

he manual injector can be mounted to suitable Fiber recoaters through the 4-40 screws around the recoater housing (see photo for the right). Utilize a 3/32″ hex key to safe the injector before use. To connect the PTRRRM to the recoater mold, tighten up the connector at the end of the eco-friendly plastic tubes, then release with a 1/4 choose permit rotation.

The injector is equipped with a syndication device as well as 2-position selection handle for directing the flow of recoat material. A knurled dispensing attach having an internal plunger acts as a syringe for the recoat materials. To fill the Yarn Binder, point the handle downwards (i.e., toward the recoat bottle), then spin the knurled dispensing screw counterclockwise till it rotates freely to fill the syringe (demonstrated in the picture for the right). Then, to inject the recoat materials into the mold, point the lever horizontally (i.e., dealing with the knurled attach) and fdrofe the attach clockwise until nearby the finish from the journey range is reached. Steer clear of bottoming out your dispenser as this may damage the inner plunger; also take care when re-interesting the threads to prevent go across threading the dispensing attach. A number of fill/inject actions may be needed till air is displaced inside the system. Use camera lens tissue and an acetone or alcoholic beverages cleaning solution to collect any extra recoat material that flows from your mold.

Yarn Binder..

We are using cookies on our website

Please confirm, if you accept our tracking cookies. You can also decline the tracking, so you can continue to visit our website without any data sent to third party services.